Коды ошибок в Canon 6085

E000 After power-on, the upper fixing roller does not reach 100 C within 5 min
E001 The temperature of the upper fixing roller exceeds 230 C for 5 sec or more
E002 After the temperature of the upper fixing roller has exceeded 100 C, it does not reach 180 C within 5 min
E003 After the temperature of the upper fixing roller has reached 180 C, it drops to 100 C or less for 5 sec or more
E005 The length used of the cleaning belt inside the fixing assembly has exceeded a specific value
E012 After the drum motor drive signal has been generated, clock pulses are not generated within 2 sec
E013 After the waste toner feeding screw has become locked, the detecting switch (SW20) is pressed a multiple number of times within a specific period of time
E014 When the fixing motor (M17) is rotating, an error is detected for 2 sec or more
E015 After the pick up motor drive signal has been generated, clock pulses have not been generated within 2 sec
E019 As many as 50,000 have been made after detecting a waste toner full condition
E020 During copying, the toner supply signal is 0', indicating the absence of toner, for 3 min or more. During toner supply sequence at time of installation, the toner supply signal does not go '1' after 6 min or more
E030 After the total copy counter has turned OFF, an open circuit is detected for the total copy counter
E032 After the clock pulse signal reached the IPC communication format of the copier DC controller PCB, the Copy Data Controller-A1 does not detect the signal
E050 While the paper jogging guide motor (M11) drive signal is being generated, the paper guide home position signal (THP) is not generated for 2 sec or more. While the paper jogging guide motor (M11) is being generated, the paper jogging guide home position signal (THP) is generated for two sec or more
E202 The scanner home position signal (SCHP) is not generated within 10 sec after the power switch or the Copy Start Key is pressed
E203 While the scanner motor drive signal is being generated, clock pulses are not generated within 2 sec
E204 The scanner leading edge signal (SCDP1) is not generated within 0.8 sec after the scanner has started to move
E209 The scanner C.F.F. position signal (SCFFP) is not generated within 10 sec after the C.F.F. has been sent
E210 The lens X home position signal (SCFFP) is not generated within 10 sec after the C.F.F. has been sent
E212 The lens Y home position signal (LYHP) is not generated within 9 sec after the power switch or the Copy Start Key is turned ON. The lens Y home position signal (LYHP) is generated for 2 sec or more
E213 In stream reading mode, the scanner original leading edge sensor 2 signal (SCDP2) is not generated for 5 pages continuously
E214 While the scanner cooling fan (FM1, FM10, FM11) is rotating, an error signal is generated for 2 sec or more
E270 In stream reading mode, the scanner leading edge signal(SCDP2) is not generated within a specific period of time after a command has been issued to lock the scanner
E710 At power-on the IPC (Q170) on the DC controller PCB cannot be initialized
E711 After power-on the IPC (Q170) on the DC controller PCB goes out of order
E712 The communication IC on the RDF controller PCB has gone out of order
E713 The communication IC on the sorter control PCB has gone out of order
E715 The communication IC on the C.F.F. controller PCB has gone out of order
E717 The communication IC on the Copy Data Controller-A1 PCB has gone out of order
E800 An open circuit is detected
E801 Current flows from the activation circuit in the absence of the scanning lamp ON signal
E802 The relay (RL3) in the power supply unit does not operate in spite of the auto power-off signal