Konica 1015
F09 Power leakage of some kind. Heat, exposure, AC or power supply.
F23 Toner motor
F26 Toner density adjustment problem. This means machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel that you should disconnect the toner motor first. This Код ошибки happens probably because either machine wasn't set up properly, or the customer kept on using the machine with the toner light on.
F28 Corona problem. Could be any corona. Must reset with "25: mode, "P45" set to "0"
F34 High fuser temperature
F35, F36 Low fuser temperature
F41 Scan home
F42 Scan home
F43 Exposure lamp
F45 Lens problem
F54 Fan motor
F60 ADF to main board communication problem
F67 ADF error
F77 Sorter gate
F88 AE adjustment problem
J11-J13 Feed jam
J16 Jam inside
J31, J32 Exit jam
J61, J62 ADF jam
J63 ADF exit jam
J72 Sorter jam
P20 Drum unit or toner level connection problem
P25 300 copies have been run since toner light came on. Depending on how 25 mode, Код ошибки 92 is set, machine may not work at all.
P26 Must adjust TDS in 47 mode
P64 ADF & operator are confused
P68, P69 ADF feed problem
P71 Sorter interlock
P81 Key counter not installed


Konica 1018
F18 Paper lift did not complete
F23 Toner motor
F24 Pre clean lamp problem
F26 Toner density sensor
F34 Fuser overheat
F35 Fuser temperature too low. Lamp, thermofuse open wire
F36 Fuser temperature erratic. Probably thermistor
F41 End of scan sensor not actuated
F42 End of scan sensor not reached
F43 CVR (copy lamp voltage regulator)
F45 Lens or mirror movement problem
F52 Drive problem
F55 Zero cross.
F56 Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
F60 ADF/machine interface problem
F67 ADF drive problem
F70 Sorter/machine interface problem
F77 Sorter bin problem
F78 Stapler problem
F86 Waste toner see 56
F98 Duplex problem
J11 Upper cassette
J12 Lower cassette
J13, J14 Paper feed jam
J15 Duplex unit jam
J16, J17 Feed jam
J19 Paper feed jam
J31, J32 Exit jam
J61 ADF opened during run
J62, J63 ADF jam
J65 RADF reverse jam
J72 Sorter jam, or sorter interlock opened
J75 Stapler jam
J92-J94 Duplex stack gate sensor or other duplex problem
J95 Duplex motor or duplex jam
P17 Right door
P19 Right door of paper feed unit
P20 Drum not installed properly or toner level sensor connection problem
P33 Left door
P61 RADF reverse cover open
P64 ADF was selected at the wrong time
P71 Sorter interlock
P74 Stapler overloaded, or paper left in stapler bin
P76 Out of staples
P81 Key counter not installed
P82 Memory card problem
P96 Paper in stacker when duplex selected
P97 Used bypass in duplex mode
P99 More than one side than the other in duplex


Konica 1112
16 Feed jam
20 Toner level detector problem or loose connection
23 Toner feed problem
25 Toner. Means that 100 copies have been made since toner light came on
26 Toner density problem
31, 32 Exit jam
34 Fuser temperature too high
35 Fuser temperature too low
36 Fuser problem. Heat, thermistor, etc.
41 Scan return
42 Scan forward
43 Exposure lamp
50 Problem with IC8
52 EnКод ошибкиr (pulse sensor, PT; drive problem)


Konica 1120
04 PTC heater. Don't know what this is, but "0" means it is not installed. 1 means it is.
F09 Power leakage of some kind. Heat, exposure, AC or power supply or main relay. Go to "25 mode" and select "P49" and reset to "0"
F23 Toner motor
F26 Toner density adjustment problem. This means the machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel you should disconnect the toner motor first. This Код ошибки happens probably because either the machine wasn't set up properly, or because the customer kept using the machine with the light on.
F28 Corona problem. Could be any corona.
F34 High fuser temperature.
F35, F36 Low fuser temperature.
F41, F42 Scan home
F43 Exposure lamp or exp. Lamp board.
F44 Lens drive problem.
F45 Lens problem.
F54 Fan motor.
F60 ADF to main board communication problem.
F67 ADF enКод ошибкиr (pulse sensor, drive problem)
F70 Sorter to machine communication problem.
F77 Sorter gate.
F88 AE adjustment problem.
J11-J13 Feed jam
J14-J16 Jam inside
J31, J32 Exit jam
J61, J62 ADF jam
J63 ADF exit jam
J72 Sorter jam
P11 Count. For total count, select "0". For developer count, select "5".
P12 Preheat mode fuser temperature. 0 for 365 degrees. 1 for 374 degrees. 2 for 383 degrees.
P15 Size priority. 0 is standard. 1 is a size priority.
P16 Paper size priority.
P19 Preheat shut off timing. 0 for 1 hour. 1 for 2 hours. 2 for 3 hours.
P20 Drum unit or toner level connection problem. Most likely, a loose connection.
P22-P24 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
P25 300 copies have been run since toner light came on, depending on how 25 mode, Код ошибки 92 is set, machine may not work at all.
P26 ADF border erase. 0 for none. 5 for 5mm.
P26 Must replace and calibrate developer.
P27 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P27 Toner density sensor unplugged or toner density sensor problem.
P28 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P64 ADF & operator are confused. Remove original.
P68, P69 ADF feed problem.
P71 Sorter interlock.
P81 Key counter not installed.


Konica 1212
04 PTC heater. Don't know what this is, but "0" means it is not installed. 1 means it is.
F09 Power leakage of some kind. Heat, exposure, AC or power supply or main relay. Go to "25 mode" and select "P49" and reset to "0"
F23 Toner motor
F26 Toner density adjustment problem. This means the machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel you should disconnect the toner motor first. This Код ошибки happens probably because either the machine wasn't set up properly, or because the customer kept using the machine with the light on.
F28 Corona problem. Could be any corona.
F34 High fuser temperature.
F35 Low fuser temperature.
F36 Low fuser temperature.
F41 Scan home
F43 Exposure lamp or exp. Lamp board.
F44 Lens drive problem.
F45 Lens problem.
F54 Fan motor.
F60 ADF to main board communication problem.
F67 ADF enКод ошибкиr (pulse sensor, drive problem)
F70 Sorter to machine communication problem.
F77 Sorter gate.
F88 AE adjustment problem.
J11-J13 Feed jam
J14-J16 Jam inside
J31, J32 Exit jam
J61, J62 ADF jam
J63 ADF exit jam
J72 Sorter jam
P11 Count. For total count, select "0". For developer count, select "5".
P12 Preheat mode fuser temperature. 0 for 365 degrees. 1 for 374 degrees. 2 for 383 degrees.
P15 Size priority. 0 is standard. 1 is a size priority.
P16 Paper size priority.
P19 Preheat shut off timing. 0 for 1 hour. 1 for 2 hours. 2 for 3 hours.
P20 Drum unit or toner level connection problem. Most likely, a loose connection.
P22-P24 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
P25 300 copies have been run since toner light came on, depending on how 25 mode, Код ошибки 92 is set, machine may not work at all.
P26 ADF border erase. 0 for none. 5 for 5mm.
P26 Must replace and calibrate developer.
P27 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P27 Toner density sensor unplugged or toner density sensor problem.
P28 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P64 ADF & operator are confused. Remove original.
P68, P69 ADF feed problem.
P71 Sorter interlock.


Konica 1290, 1290RE
16 Feed jam
20 Toner sensor connector
25 Toner light has been on for 100 copies
26 Toner density sensor
31 Exit switch not actuated
32 Exit jam
34 Fuser problem
35 Low fuser temperature
36 High fuser temperature
41 Scan did not return home
42 Scan problem
43 Exposure lamp problem
50 Board problem
52 Drive problem
85 No waste bottle


Konica 1590
F23 Toner motor problem
F24 Pre-clean lamp
F26 Toner ratio
F34 High fuser temperature
F35 Low fuser temperature
F36 Thermistor
F41 Scan home
F42 Forward scan exposure lamp
F43 Exposure lamp
F45 Lens drive
F50 Board problem
F52 Drive
F77 Sorter bin sensor
J12, J13 Paper feed jam
J16 Paper feed jam
J31 Jam under drum
J32 Exit jam
J72 Sorter jam
P20 Drum not installed properly
P71 Sorter cover


Konica 1790
F34 High fuser temperature
F35 Low fuser temperature
F36 Open thermistor or incomplete warm up
F41 Scan home problem
F42 Scan problem
F43 CVR board problem
F45 Lens drive
F52 Drive
F55 Zero cross problem
F67 ADF drive
F77 Sorter drive
J11 Upper cassette jam
J12 Lower cassette jam
J14 LCT jam
J16 Cassette jam
J31, J32 Jam under drum
J62, J63 ADF jam
J72 Sorter jam
P14 LCT open
P61 ADF up
P64 Original on glass
P69 ADF original jam
P71 Sorter cover open
P81 Key counter out


Konica 2020
F18 Paper lift did not complete
F23 Toner motor
F24 Pre clean lamp problem
F26 Toner density sensor
F34 Fuser overheat
F35 Fuser temperature too low. Lamp, thermofuse open wire
F36 Fuser temperature erratic. Probably thermistor
F41 End of scan sensor not actuated
F42 End of scan sensor not reached
F43 CVR (copy lamp voltage regulator)
F45 Lens or mirror movement problem
F52 Drive problem
F55 Zero cross.
F56 Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
F60 ADF/machine interface problem
F67 ADF drive problem
F70 Sorter/machine interface problem
F77 Sorter bin problem
F78 Stapler problem
F86 Waste toner see 56
F98 Duplex problem
J11 Upper cassette
J12 Lower cassette
J13, J14 Paper feed jam
J15 Duplex unit jam
J16, J17 Feed jam
J19 Paper feed jam
J31, J32 Exit jam
J61 ADF opened during run
J62, J63 ADF jam
J65 RADF reverse jam
J72 Sorter jam, or sorter interlock opened
J75 Stapler jam
J92-J94 Duplex stack gate sensor or other duplex problem
J95 Duplex motor or duplex jam
P17 Right door
P19 Right door of paper feed unit
P20 Drum not installed properly or toner level sensor connection problem
P33 Left door
P61 RADF reverse cover open
P64 ADF was selected at the wrong time
P71 Sorter interlock
P74 Stapler overloaded, or paper left in stapler bin
P76 Out of staples
P81 Key counter not installed
P82 Memory card problem
P96 Paper in stacker when duplex selected
P97 Used bypass in duplex mode
P99 More than one side than the other in duplex


Konica 2028
F18 Paper lift did not complete
F23 Toner motor
F24 Pre clean lamp problem
F26 Toner density sensor
F34 Fuser overheat
F35 Fuser temperature too low. Lamp, thermofuse open wire
F36 Fuser temperature erratic. Probably thermistor
F41 End of scan sensor not actuated
F42 End of scan sensor not reached
F43 CVR (copy lamp voltage regulator)
F45 Lens or mirror movement problem
F52 Drive problem
F55 Zero cross
F56 Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
F60 ADF/machine interface problem
F67 ADF drive problem
F70 Sorter/machine interface problem
F77 Sorter bin problem
F78 Stapler problem
F86 Waste toner see 56
F98 Duplex problem
J11 Upper cassette
J12 Lower cassette
J13, J14 Paper feed jam
J15 Duplex unit jam
J16, J17 Feed jam
J19 Paper feed jam
J31, J32 Exit jam
J61 ADF opened during run
J62, J63 ADF jam
J65 RADF reverse jam
J72 Sorter jam, or sorter interlock opened
J75 Stapler jam
J92-J94 Duplex stack gate sensor or other duplex problem
J95 Duplex motor or duplex jam
P17 Right door
P19 Right door of paper feed unit
P20 Drum not installed properly or toner level sensor connection problem
P33 Left door
P61 RADF reverse cover open
P64 ADF was selected at the wrong time
P71 Sorter interlock
P74 Stapler overloaded, or paper left in stapler bin
P76 Out of staples
P81 Key counter not installed
P82 Memory card problem
P96 Paper in stacker when duplex selected
P97 Used bypass in duplex mode
P99 More than one side than the other in duplex


Konica 2125
F18 Paper feed lift problem
F18-3 LCT problem
F18-4 LCT problem
F28-1 Charge corona
F28-2 Transfer or separator corona
F34-1 High fuser temperature
F34-2 High fuser temperature
F35-1 Low fuser temperature
F35-2 Low fuser temperature
F36-1 Low fuser temperature
F36-2 Low fuser temperature
F41 Scan return problem
F42 Scan forward problem
F43 Exposure lamp board problem
F45 Lens home problem
F52 Main motor drive problem
F55 Zero cross of DC power supply
F60 Communication interruption between the machine and RADF
F67 RDH or RADF drive problem
F70 Communication problem between machine and sorter
F77 Sorter bin problem
F78 No memory card installed
F86 Too many copies were made after toner waste was full. Reset with 47 mode, Код ошибки 94.
F98 Duplex guide plate does not return home quickly enough
J10 Feed jam
J11 Upper feed jam
J12 Lower feed jam
J13 Upper paper feed unit jam
J14, J15 Lower paper feed unit jam
J16, J17 Jam in machine
J19 Paper feed unit jam
J21 Jam around drum
J31 Exit jam
J32 Exit jam
J61, J62 RDH/RADF jam or open
J63 RADF exit jam
J72 Sorter jam or open interlock
J74 Finisher problem
J75 Stapler problem
J92-J95 Duplex jam
P17 Right side door open
P19 Paper feed unit door open
P33 Exit door open
P51 Front door open
P61 RADF cover open
P64 RADF not opened to remove originals
P68 Original removed during operation of RADF
P69 Original didn't feed during RADF/RDH operation
P71 Sorter interlock
P74 51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
P76 Out of staples
P78 Stapler not installed
P81 Key counter not plugged in
P82 Memory card not installed, not formatted to Konica specs, or no machine serial number registered on memory card
P86 No toner waste box
P91 Duplex unit pulled out
P96 Paper in duplex tray
P97 Bypass was used or attempted during duplex.
P99 Too many reverse side copies during duplex


Konica 2130
F18 Paper feed lift problem
F18-3 LCT problem
F18-4 LCT problem
F28-1 Charge corona
F28-2 Transfer or separator corona
F34-1 High fuser temperature
F34-2 High fuser temperature
F35-1 Low fuser temperature
F35-2 Low fuser temperature
F36-1 Low fuser temperature
F36-2 Low fuser temperature
F41 Scan return problem
F42 Scan forward problem
F43 Exposure lamp board problem
F45 Lens home problem
F52 Main motor drive problem
F55 Zero cross of DC power supply
F60 Communication interruption between the machine and RADF
F67 RDH or RADF drive problem
F70 Communication problem between machine and sorter
F77 Sorter bin problem
F78 No memory card installed
F86 Too many copies were made after toner waste was full. Reset with 47 mode, Код ошибки 94.
F98 Duplex guide plate does not return home quickly enough
J10 Feed jam
J11 Upper feed jam
J12 Lower feed jam
J13 Upper paper feed unit jam
J14 Lower paper feed unit jam
J15 Lower paper feed unit jam
J16, J17 Jam in machine
J19 Paper feed unit jam
J21 Jam around drum
J31, J32 Exit jam
J61 RDH/RADF jam or open
J62 RDH/RADF jam
J63 RADF exit jam
J72 Sorter jam or open interlock
J74 Finisher problem
J75 Stapler problem
J92-J95 Duplex jam
P17 Right side door open
P19 Paper feed unit door open
P33 Exit door open
P51 Front door open
P61 RADF cover open
P64 RADF not opened to remove originals
P68 Original removed during operation of RADF
P69 Original didn't feed during RADF/RDH operation
P71 Sorter interlock
P74 51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
P76 Out of staples
P78 Stapler not installed
P81 Key counter not plugged in
P82 Memory card not installed, not formatted to Konica specs, or no machine serial number registered on memory card
P86 No toner waste box
P91 Duplex unit pulled out
P96 Paper in duplex tray
P97 Bypass was used or attempted during duplex.
P99 Too many reverse side copies during duplex


Konica 2203
F35 Low Temperature
F41, F42 Optics
F43 CVR
F46 Lens drive
F51 Door
F52 Drive
J11 Upper PF jam
J12 Lower PF jam
J13 Jam
J21 Separator jam
J31 Transport jam
J32 Jam
P81 Key counter


Konica 2290
1 Sort jam
61 ADF/RADF open door
64 Original on glass
97 Duplex paper wrong size selected
99 Duplex fed double
F35, F36 Fuser
F41 Scan return
F42 Scan forward problem
F43 Exposure stays on
F46 Lens position problem
F52 Drive
F53 Developer unit shift problem
F67 ADF/RADF drive problem
F98 Duplex side to side gate problem
J11 Upper cassette jam
J12 Lower cassette jam
J13 LCT jam
J14 Jam
J15 Paper feed jam
J21 Jam under/around drum
J31 Transport jam
J32 Exit ajm
J61 RADF jam
J62 ADF
J63 ADF exit jam
J65 ADF
J72 Sort jam
J92-J96 Duplex jams
P81 Key counter


Konica 2590
F34 High fuser temperature
F35 Low fuser temperature at warm up
F36 Low fuser temperature after warm up
F41 No scan
F42 No return scan
F43 Exposure lamp stays on
F45 Lens
F52 Drive
F55 Zero cross signal to main board
F67 ADF drive
F77 Sorter drive
F98 Duplex problem
J11 Bypass jam
J12 Middle cassette jam
J13 Lower cassette jam
J14 LCT jam
J15 Duplex jam
J16 Paper feed jam
J17 Registration jam
J31 Internal jam
J32 Exit jam
J61 ADF opened during runADF jam
J62, J63 ADF exit jam
J65 RADF jam
J72 Sorter jam
J92-J96 Duplex jams
P14 LCT cover open
P61 RADF cover open
P64 Original on glass
P69 RADF jam in sheet feet mode
P71 Sorter cover open
P81 Key counter
P96 Paper still in duplex tray
P97 Wrong size selected for duplex
P99 Duplex confused by double fed originals


Konica 3035
F18 Paper lift did not complete
F23 Toner motor
F24 Pre clean lamp problem
F26 Toner density sensor
F34 Fuser overheat
F35 Fuser temperature too low. Lamp, thermofuse open wire
F36 Fuser temperature erratic. Probably thermistor
F41 End of scan sensor not actuated
F42 End of scan sensor not reached
F43 CVR (copy lamp voltage regulator)
F45 Lens or mirror movement problem
F52 Drive problem
F55 Zero cross
F56 Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
F60 ADF/machine interface problem
F67 ADF drive problem
F70 Sorter/machine interface problem
F77 Sorter bin problem
F78 Stapler problem
F86 Waste toner see 56
F98 Duplex problem
J11 Upper cassette
J12 Lower cassette
J13, J14 Paper feed jam
J15 Duplex unit jam
J16, J17 Feed jam
J19 Paper feed jam
J31, J32 Exit jam
J61 ADF opened during run
J62, J63 ADF jam
J65 RADF reverse jam
J72 Sorter jam, or sorter interlock opened
J75 Stapler jam
J92-J94 Duplex stack gate sensor or other duplex problem
J95 Duplex motor or duplex jam
P17 Right door
P19 Right door of paper feed unit
P20 Drum not installed properly or toner level sensor connection problem
P33 Left door
P61 RADF reverse cover open
P64 ADF was selected at the wrong time
P71 Sorter interlock
P74 Stapler overloaded, or paper left in stapler bin
P76 Out of staples
P81 Key counter not installed
P82 Memory card problem
P96 Paper in stacker when duplex selected
P97 Used bypass in duplex mode
P99 More than one side than the other in duplex


Konica 3135
F18 Paper feed lift problem
F18-3 LCT problem
F18-4 LCT problem
F28-1 Charge corona
F28-2 Transfer or separator corona
F34-1 High fuser temperature
F34-2 High fuser temperature
F35-1 Low fuser temperature
F35-2 Low fuser temperature
F36-1 Low fuser temperature
F36-2 Low fuser temperature
F41 Scan problem
F42 Scan forward problem
F43 Exposure lamp board problem
F45 Lens home problem
F52 Main motor drive problem
F55 Zero cross of DC power supply
F60 Communication interruption between machine and RADF
F67 RDH or RADF drive problem
F70 Communication problem between machine and sorter
F77 Sorter, finisher, or stapler problem
F86 Too many copies were made after toner waste was full
F98 Duplex problem
J10 Feed jam
J11, J12 Jam in machine
J13 LCT jam
J14 LCT jam
J15 Duplex feed jam
J16, J17 Jam in machine
J19 LCT jam
J21 Jam around drum
J31 Jam in machine
J32 Exit jam
J61, J62 RDH/RADF jam
J63 RADF exit jam
J72 Sorter jam or open interlock
J74 Finisher problem
J75 Stapler problem
J92 Duplex jam
J93 Duplex jam
J94 Duplex jam
J95 Duplex jam
P17 Paper feed door open
P19 LCT door open
P33 Exit door open
P51 Front door open
P61 RADF cover open
P64 RADF not opened to remove originals
P64 RDH original width different with guide width
P68 Original removed during operation or RADF
P69 Original didn't feed during RADF/RDH operation
P71 Sorter interlock
P74 51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode
P76 No staples
P78 Stapler not installed
P81 Key counter not plugged in
P86 No toner waste box
P91 Duplex unit pulled out
P96 Paper in duplex tray
P97 Wrong size paper during duplex
P99 Too many reverse side copies during duplex.


Konica 3240
F10-1 Paper feed or duplex communication problem
F10-2 Paper feed or duplex communication problem
F10-3 Paper feed unit connection problem
F10-4 Internal temperature problem
F18-1 Upper feed lift problem
F18-2 Lower paper feed lift problem
F18-3 Upper paper feed lift problem
F18-4 Middle paper feed unit problem
F18-5 Lower paper feed unit lift problem
F28-1 Transfer separator corona
F28-2 Charge corona
F34-1 High fuser temperature or bad thermistor
F34-2 High fuser temperature
F35-1 Low fuser temperature or open thermistor
F35-2 Low fuser temperature
F36-1 Low fuser temperature
F42-1 Scan forward problem
F42-2 Scan home problem
F42-3 Scan problem
F43-1 Exposure lamp board problem
F43-2 Exposure lamp board problem
F43-3 Exposure lamp board problem
F44-1 Optics communication problem
F45-1 Lens home problem
F45-2 Mirror home problem
F51-2 Main motor speed problem
F52-1 Cooling fan problem
F52-2 Suction (transport) fan problem
F52-4 Optics cooling fan problem (2 fans; could be either one)
F60 Communication interruption between machine and RADF
F67 RDH or RADF pressure home sensor or pressure motor.
F70 Communication problem between machine and sorter
F76 Stapler problem
F77 Sorter bin problem
F78 No memory card installed
F80 Communication problem between machine and weekly timer
F81 Communication problem between machine and memory card
F97 Duplex up down plate problem
F98 Duplex guide plate problem
F99 Duplex indexer problem
J10 Feed jam
J11 Upper feed jam
J12 Lower feed jam
J13 Upper paper feed unit jam
J14 Lower paper feed unit jam
J15 Duplex feed jam
J17 Jam in machine
J17-7 Jam at paper feed unit exit
J18 Jam in machine from middle tray of paper feed unit
J31, J32 Exit jam
J61 RADF opened during run, or other RADF jam
J62 RDH/RADF jam
J63 RADF feed jam
J72 Sorter jam or open interlock
J74 Finisher problem
J75 Stapler problem
J92 Reversal sensor jam
J97-1 Stacker entrance jam
J97-2 Stacker entrance jam
J98 Stacker entrance jam
P17 Right side door open
P19 Paper feed unit door open
P33 Exit door open
P51 Front door open
P61 RADF cover open
P64 RADF not opened to remove originals
P68 Original removed during operation of the RADF
P69 Original didn't feed during RADF/RDH operation
P71 Sorter interlock
P74 51 copies or more went to the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
P76 Out of staples
P78 Stapler not installed
P81 Key counter not plugged in
P82 Memory card not installed, not formatted to Konica specs, or no machine serial # registered on memory card.
P86 No toner waste box
P91 Duplex unit pulled out
P96 Paper in duplex tray
P97 Bypass was used or attempted during duplex
P99 Too many reverse side copies during duplex


Konica 3290
51 Door open
64 Original still on glass
71 Sorter interlock
91 Duplex interlock
97 Incorrect mode selected
99 Duplex problem
F35 Fuser
F41 Scan return
F42 Scan
F43 Exposure lamp
F46 Lens drive
F52 Machine drive
F67 RADF
F98 Duplex unit
J11 Upper cassette jam
J12 Lower cassette jam
J13 LCT jam
J14 Paper feed jam
J15 Duplex jam
J21 Drum wrap jam
J31 Transport jam
J32 Fuser jam
J61 RADF cover
J62 RADF feed
J63 RADF exit
J65 RADF jam
J72 Sorter jam
J94-J96 Duplex jam or paper still in duplex unit
P81 Key counter


Konica 3340
F10-1 Paper feed or duplex communication problem
F10-2 Paper feed or duplex communication problem
F10-3 Paper feed unit connection problem
F10-4 Internal temperature problem
F18-1 Upper feed lift problem
F18-2 Lower paper feed lift problem
F18-3 Upper paper feed lift problem
F18-4 Middle paper feed unit problem
F18-5 Lower paper feed unit lift problem
F28-1 Transfer separator corona
F28-2 Charge corona
F34-1 High fuser temperature or bad thermistor
F34-2 High fuser temperature
F35-1 Low fuser temperature or open thermistor
F35-2 Low fuser temperature
F36-1 Low fuser temperature
F42-1 Scan forward problem
F42-2 Scan home problem
F42-3 Scan problem
F43-1 Exposure lamp board problem
F43-2 Exposure lamp board problem
F43-3 Exposure lamp board problem
F44-1 Optics communication problem
F45-1 Lens home problem
F45-2 Mirror home problem
F51-2 Main motor speed problem
F52-1 Cooling fan problem
F52-2 Suction (transport) fan problem
F52-4 Optics cooling fan problem (2 fans; could be either one)
F60 Communication interruption between machine and RADF
F67 RDH or RADF pressure home sensor or pressure motor.
F70 Communication problem between machine and sorter
F76 Stapler problem
F77 Sorter bin problem
F78 No memory card installed
F80 Communication problem between machine and weekly timer
F81 Communication problem between machine and memory card
F97 Duplex up down plate problem
F98 Duplex guide plate problem
F99 Duplex indexer problem
J10 Feed jam
J11 Upper feed jam
J12 Lower feed jam
J13 Upper paper feed unit jam
J14 Lower paper feed unit jam
J15 Duplex feed jam
J17 Jam in machine
J17-7 Jam at paper feed unit exit
J18 Jam in machine from middle tray of paper feed unit
J31, J32 Exit jam
J61 RADF opened during run, or other RADF jam
J62 RDH/RADF jam
J63 RADF feed jam
J72 Sorter jam or open interlock
J74 Finisher problem
J75 Stapler problem
J92 Reversal sensor jam
J97-1 Stacker entrance jam
J97-2 Stacker entrance jam
J98 Stacker entrance jam
P17 Right side door open
P19 Paper feed unit door open
P33 Exit door open
P51 Front door open
P61 RADF cover open
P64 RADF not opened to remove originals
P68 Original removed during operation of the RADF
P69 Original didn't feed during RADF/RDH operation
P71 Sorter interlock
P74 51 copies or more went to the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
P76 Out of staples
P78 Stapler not installed
P81 Key counter not plugged in
P82 Memory card not installed, not formatted to Konica specs, or no machine serial # registered on memory card.
P86 No toner waste box
P91 Duplex unit pulled out
P96 Paper in duplex tray
P97 Bypass was used or attempted during duplex


Konica 4045
F18 Paper lift did not complete
F23 Toner motor
F24 Pre clean lamp problem
F26 Toner density sensor
F34 Fuser overheat
F35 Fuser temperature too low. Lamp, thermofuse open wire
F36 Fuser temperature erratic. Probably thermistor
F41 End of scan sensor not actuated
F42 End of scan sensor not reached
F43 CVR (copy lamp voltage regulator)
F45 Lens or mirror movement problem
F52 Drive problem
F55 Zero cross.
F56 Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
F60 ADF/machine interface problem
F67 ADF drive problem
F70 Sorter/machine interface problem
F77 Sorter bin problem
F78 Stapler problem
F86 Waste toner see 56
F98 Duplex problem
J11 Upper cassette
J12 Lower cassette
J13, J14 Paper feed jam
J15 Duplex unit jam
J16, J17 Feed jam
J19 Paper feed jam
J31, J32 Exit jam
J61 ADF opened during run
J62, J63 ADF jam
J65 RADF reverse jam
J72 Sorter jam, or sorter interlock opened
J75 Stapler jam
J92-J94 Duplex stack gate sensor or other duplex problem
J95 Duplex motor or duplex jam
P17 Right door
P19 Right door of paper feed unit
P20 Drum not installed properly or toner level sensor connection problem
P33 Left door
P61 RADF reverse cover open
P64 ADF was selected at the wrong time
P71 Sorter interlock
P74 Stapler overloaded, or paper left in stapler bin
P76 Out of staples
P81 Key counter not installed
P82 Memory card problem
P96 Paper in stacker when duplex selected
P97 Used bypass in duplex mode
P99 More than one side than the other in duplex


Konica 4065
11-1 Paper feed jam
11-10 RADF jam
11-11 Sorter jam
11-12 Sorter jam
11-2 Paper feed jam
11-3 Registration area jam
11-4 Paper jam around drum (drum wrap jam)
11-5 Jam in transport area
11-6 Exit jam or duplex exit jam
11-7 Duplex reversing sensor jam or duplex feed jam
11-8 Duplex jam
11-9 Duplex jam


Konica 4145
F18 Paper feed lift problem
F18-3 LCT problem
F18-4 LCT problem
F28-1 Charge corona
F28-2 Transfer or separator corona
F34-1 High fuser temperature
F34-2 High fuser temperature
F35-1 Low fuser temperature
F35-2 Low fuser temperature
F36-1 Low fuser temperature
F36-2 Low fuser temperature
F41 Scan problem
F42 Scan forward problem
F43 Exposure lamp board problem
F45 Lens home problem
F52 Main motor drive problem
F55 Zero cross of DC power supply
F60 Communication interruption between machine and RADF
F67 RDH or RADF drive problem
F70 Communication problem between machine and sorter
F77 Sorter, finisher, or stapler problem
F86 Too many copies were made after toner waste was full
F98 Duplex problem
J10 Feed jam
J11, J12 Jam in machine
J13 LCT jam
J14 LCT jam
J15 Duplex feed jam
J16, J17 Jam in machine
J19 LCT jam
J21 Jam around drum
J31 Jam in machine
J32 Exit jam
J61, J62 RDH/RADF jam
J63 RADF exit jam
J72 Sorter jam or open interlock
J74 Finisher problem
J75 Stapler problem
J92-J95 Duplex jam
P17 Paper feed door open
P19 LCT door open
P33 Exit door open
P51 Front door open
P61 RADF cover open
P64 RADF not opened to remove originals
P64 RDH original width different with guide width
P68 Original removed during operation or RADF
P69 Original didn't feed during RADF/RDH operation
P71 Sorter interlock
P74 51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode
P76 No staples
P78 Stapler not installed
P81 Key counter not plugged in
P86 No toner waste box
P91 Duplex unit pulled out
P96 Paper in duplex tray
P97 Wrong size paper during duplex
P99 Too many reverse side copies during duplex.


Konica 4155
F18 Paper feed lift problem
F18-3 LCT problem
F18-4 LCT problem
F28-1 Charge corona
F28-2 Transfer or separator corona
F34-1 High fuser temperature
F34-2 High fuser temperature
F35-1 Low fuser temperature
F35-2 Low fuser temperature
F36-1 Low fuser temperature
F36-2 Low fuser temperature
F41 Scan problem
F42 Scan forward problem
F43 Exposure lamp board problem
F45 Lens home problem
F52 Main motor drive problem
F55 Zero cross of DC power supply
F60 Communication interruption between machine and RADF
F67 RDH or RADF drive problem
F70 Communication problem between machine and sorter
F77 Sorter, finisher, or stapler problem
F86 Too many copies were made after toner waste was full
F98 Duplex problem
J10 Feed jam
J11 Jam in machine
J12 Jam in machine
J13, J14 LCT jam
J15 Duplex feed jam
J16, J17 Jam in machine
J19 LCT jam
J21 Jam around drum
J31 Jam in machine
J32 Exit jam
J61, J62 RDH/RADF jam
J63 RADF exit jam
J72 Sorter jam or open interlock
J74 Finisher problem
J75 Stapler problem
J92-J95 Duplex jam
P17 Paper feed door open
P19 LCT door open
P33 Exit door open
P51 Front door open
P61 RADF cover open
P64 RADF not opened to remove originals
P64 RDH original width different with guide width
P68 Original removed during operation or RADF
P69 Original didn't feed during RADF/RDH operation
P71 Sorter interlock
P74 51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode
P76 No staples
P78 Stapler not installed
P81 Key counter not plugged in
P86 No toner waste box
P91 Duplex unit pulled out
P96 Paper in duplex tray
P97 Wrong size paper during duplex
P99 Too many reverse side copies during duplex.


Konica 4255
F18 Paper feed lift problem
F18-3 LCT problem
F18-4 LCT problem
F28-1 Charge corona
F28-2 Transfer or separator corona
F34-1 High fuser temperature
F34-2 High fuser temperature
F35-1 Low fuser temperature
F35-2 Low fuser temperature
F36-1 Low fuser temperature
F36-2 Low fuser temperature
F41 Scan problem
F42 Scan forward problem
F43 Exposure lamp board problem
F45 Lens home problem
F52 Main motor drive problem
F55 Zero cross of DC power supply
F60 Communication interruption between machine and RADF
F67 RDH or RADF drive problem
F70 Communication problem between machine and sorter
F77 Sorter, finisher, or stapler problem
F86 Too many copies were made after toner waste was full
F98 Duplex problem
J10 Feed jam
J11, J12 Jam in machine
J13, J14 LCT jam
J15 Duplex feed jam
J16, J17 Jam in